ASTM A554 Gr 316L Stainless Steel Square Hollow Sections Specification.Specifications ASTM A554 / ASME SA554(Ornamental Tubing Specification) or ASTM A 312 Size 20x20mm to 400x400mm,other non standard sizes available on request Wall Thickness 0.5mm to 6mm Length Up to 6 meters,custom cut lengths Type Seamless/ Welded / ERW Finish 2B,No.1 Pickled Finish,No.4 finish,BAERW Pipes Tubes Dana Steel UAE - Adding Value to Steel Long Steel.Angles/Channels/Bars; ERW Pipes Tubes; Steel Service Center.Coil Cutting Cut-to-length; Coil Slitting; Sheet Perforation; Custom Fabrication; Pre-Engineered Buildings.Steel Buildings(Primary) Single Skin Profile Sheets.DSS 35/200; DSS 45/250; DSS 45/150; DTP 42/205; DSS 76/18; Profiles Cladding.Floor Decking Sheets.DSD 45 ERW Rectangular Hollow Section - Franklin SteelCertified to British/EU Specifications ERW Rectangular Hollow Section (RHS) ranges from 20 x 10mm up to 150 x 50mm in size.Thicknesses range from 0.9mm up to 3.0mm.
ERW square steel tube and pipe is available in a large selection of sizes and wall thickness options.The square steel tube range from Permanent is quality assured through our rigorous supplier selection process and is supplied to you in full compliance to BS EN 10305-3/5 Grade E220.Hollow Sections Steel RHS,CHS,SHS GB/T 13793 Longitudinal electric resistance welded steel tubes.GB/T 6728 Cold formed steel hollow sections for general structureDimensions,shapes,weight and permissble deviations.ASTM A500 Cold Formed Welded and Seamless Carbon Steel Steel Structural Tubing in Round and ShapesHot Finish EN 10210 S355J2H Square Hollow Section,SHS EN 10210 S355J2H Square Hot Finish Hollow Section Specification.Standard BS EN 10210 - Hot finished structural hollow sections of non-alloy and fine grain steels Grade S355J2H SHS (Square Hollow Sections) Sizes 20*20mm-400*400mm Wall Thickness 0.5mm - 25mm Length 6000-14000 mm Type Seamless/ Welded / ERW Dimensional Tolerances Thickness (All sizes +/- 10%)
imagesCold Formed Square Hollow Section,SHS Pipe and TubeCold Formed Square Hollow Section Specification.Standard BS EN 10219 - Cold Formed Welded Structural Hollow Sections of Non-alloy and Fine Grain Steels SHS (Square Hollow Sections) Sizes 20*20mm-400*400mm Wall Thickness 0.5mm - 25mm Length 6000-14000 mm Type Seamless/ Welded / ERW Dimensional Tolerances Thickness (All sizes +/- 10%) Packing In bundles,MS Hollow Section Some results are removed in response to a notice of local law requirement.For more information,please see here.
Rama Steel Tubes Limited Some results are removed in response to a notice of local law requirement.For more information,please see here.Previous123456NextMild Steel Hollow Sections Square Tube,Square Structural Tube,Hollow SectionStainless Steel Pipe; Hollow Section; Pipe Fittings; Coating; English.Spanish. Products > Hollow Section Square Tube.Rectangular SS Tube; ERW Rectangular Tube; Galvanised Square Tube; Stainless Square Tube; ERW Square Steel Tube; Rectangular Tube; Inquiry Email [email protected] Tube.Standard ASTM A500 Grade B,ASTM
Erw Hollow Section Galvanized Square Tube Q345 ERW Hollow Section Hot Dipped Galvanized Square Steel Pipe And Tube 100*100 US $519.00-$549.00 / Ton 1 Ton (Min.Order)Sturdy,Stainless square steel pipe tube 150 x 150 for The square steel pipe tube 150 x 150 you can find on the site are generally built using hot-dipped technology to prevent rusting and weakening of the structural elements.With seamless welding quality,these square steel pipe tube 150 x 150 are annealed with nitrogen protection and are polished with utter professionalism.These products are